Kiln Models: KM818 • KM1018 • KM1027 • KM1218 • KM1227
Other KilnMaster Parts • Manual Kilns

Repair: Services • Element Pins & Staples • Peephole Plugs
Bricks • Patches & Cement

Basic Kiln Repair: Is Your Kiln Working Right?

Electric kilns with manual controls were little more than giant-sized toasters, but computerized kilns are high-performance machines. The computer controllers demand exact temperatures, specific durations, and precisely controlled heating and cooling curves for optimal firing results. To get peak performance, you have to keep your kiln in peak operating condition. This page lists the parts most commonly needed for maintenance or repair of Skutt's KilnMaster computerized kilns.

We also have parts to Skutt glass kilns! If you don't see the parts you need for your kiln, call us. These are just a few of the parts available from Georgies, and we can quickly get the parts we don't have in stock. We can help find parts for other brands and styles of kilns, too.

Thermocouples A thermocouple reads the temperature inside the kiln, which tells the computer what to do next. The life of your thermocouple may vary, depending on how often you fire and to what temperature. When the thermocouple stops sending the temperature reading back to the computer, a FAIL message appears on the display. You must replace the thermocouple before the kiln will work again.

Elements & Relays Kiln elements wear down a little with each firing, like tires on a car with each mile driven. If the elements can't deliver heat as required by the computer, the kiln can't achieve the optimal rate of temperature increase and it shuts down. Relays, which control the flow of power between sections of the kiln, should also be replaced when you install full sets of elements. Worn relays may stay open constantly, allowing sections of the kiln to function at constant "high" settings -- or never shut off.

Kiln element prices in the tables below are for EACH element.When the table shows "2 in kiln," that section of the kiln needs TWO elements at that cost: 2 @ $38 = $76 to replace the elements for that section of your kiln. When you have to replace an element, we recommend replacing all the elements in that section of your kiln at the same time. You might even consider replacing all your kiln elements at the same time: if one is worn to the point where you have to replace it, others may not be far behind.

All Skutt elements wrap twice in the body of the kiln. They come with connectors and pins. Please specify which voltages and power phase ratings your kiln needs when ordering elements. We stock only Skutt kiln elements. Elements for other kilns may be available from their respective manufacturers by prepaid special order only.

Repair: Services

We no longer offer repair services for kilns or other equipment here at Georgies, but we can offer you these resources. Please contact these local small businesses directly to ask about their services:

Repair: Kiln Parts by Model

KM818 Kiln (chamber 17-1/2 x 18")

KM1018 Kiln (chamber 23-3/8 x 18")

KM1027 Kiln (chamber 23-3/8 x 27 ")

KM1218 Kiln (chamber 28-1/8 x 18")

KM1227-3 Kiln (chamber 28-1/8 x 27 ")

Other KilnMaster Parts

Parts for Manual Kilns

We have parts and manuals for Skutt kilns with manual controls, and also for Dawson Kiln-Sitters. Please contact us by phone or email for information on availability and prices. These are just a few of the parts we have available.

Repair: Supplies

We also carry ITC kiln coating products. ITC products repair and extend the life of all kiln interiors made of insulating fire brick, hard brick or fiber blanket. These materials are easily applied (best by spraying, which requires respiratory protection) in a matter of hours and yield outstanding results in greater firing efficiency, lowered fuel and energy costs, and lowered firing time. We stock the ITC100HT coating, and other products are available by special order. Please call or email us for availability and current pricing.